The following list is different parts I will carry that will make your swap to LED lights easier. Each user will have different needs. Please contact me if you are not exactly sure of what you need.
I'm offering these as part of the light package. If you need more, I can supply in very small quantities.
I'm offering these as part of the light package. If you need more, I can supply in very small quantities.
These are the stainless steel screws that I will be providing with each lamp. If you want extra then I will sell them in sets of two. One set will do one lens. Please note, if you order a set of lights, those lights will come with stainless screws.
If your connectors are old and corroded and not allowing a good connection, then you owe it to yourself to get a set of new connectors. Sold as a set of male and female with 12" pigtails and butt splice connectors upon request.
Your common signal flasher uses the current draw of the light bulbs to heat up two thin peices of metal that expand at two different rates. Once they heat up and expand, the flasher turns off until the two metal strips cool. Once they cool and again make contact the current flows and the process starts all over again. By using LEDs instead of light bulbs the current flow is DRASTICALLY reduced through the flasher unit. This means that your turn signals will turn on and stay on for a very long time, with only a quick off cycle. To combat this problem I am offering an electronic flasher unit that does NOT depend on current flow. Now your turn signals will flash the same speed all the time, regardless! This flasher will also work for the Hazard Lights flasher unit. If you are purchasing a set of both front and rear LED lights, then I would recommend you getting two flasher units, one for turn signals and one for the hazards. Note, if you buy a set of taillights or a complete vehicle set then you will receive ONE (1) electronic flasher.
If your old lenses are cracked, faded, or missing then I can supply you with new ones. I can get the early '66 style with no clear backup light provision, the common taillight with backup light provision, either the amber or red side marker lenses, and either size front turn signal lens in either amber OR clear. The LED's I use are colored so by using the clear lens you will still get the color effect.
If you are rebuilding your old lights and need more gaskets than what I supply in the kit then get them all at one stop. I can supply any lens to bucket gasket for all '66 - '77 applications.
|
Ring terminals |
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
$0.60 each |
|
Ring terminals |
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
$0.60 each |
|
Stainless Steel Lens |
. . . . . . . . . . #12 x 1.25". . . . . . . . . . . . |
$0.30 set of two |
|
Stainless Steel Lens |
. . . . . . . . . . #12 x .5" . . . . . . . . . . . . . . |
$0.25 set of two |
|
WeatherPak Connectors |
|
|
|
|
2 PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . |
$12.86 |
|
|
3 PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . |
$19.11 |
|
|
4 PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . |
$23.29 |
|
Electronic Flasher Unit |
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
$4.00 each |
|
TAILLIGHTS |
'66 ONLY, NO BACKUP LIGHTS . . . . . . . . . . . . |
$33 EACH |
|
TURN SIGNAL LENS |
'66 - '68 SMALL STYLE . . . . . . . . . . . . . . . . . . . . |
CLEAR $9 EACH |
|
|
'69 - '77 LARGE STYLE . . . . . . . . . . . . . . . . . . . . . |
CLEAR $9 EACH |
|
SIDE MARKERS |
FRONT AMBER . . . . . . . . . . . . . . . . . . . . . . . .
. . |
$12 EACH |
|
TAILLIGHT HOUSING |
'66 w/out backup lights . . . . . . |
$6 ea |
|
TURN SIGNAL HOUSING |
'66 - '68 small housing . . . . . . . . |
$ 2 ea |